09-13 GE Honda Fit rear camber kit

09-13 GE Honda Fit rear camber kit

-1 Degree / No thank you
$475.99
Skip to product information
09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
  • 09-13 GE Honda Fit rear camber kit
09-13 GE Honda Fit rear camber kit

09-13 GE Honda Fit rear camber kit

$475.99
Camber Degree
Front Camber Bolts

Introducing the only off the shelf option on the market to add rear camber to your USDM GE Honda Fit! 

Due to the cost of the spindle material, these are currently for pre-order only. Pre-order window will only last for 5 days and will end July 18th. Once the pre-order window has ended, please expect a 2-3 week wait before shipment, however it will most likely be sooner. There will be no refunds once your order is in and material is ordered. If there is enough interest they will be kept in stock moving forward.

There will be some modifications required for these to bolt up to your rear axle beam, please see photos for details. These are very simple to install but It is recommended that these be installed by an experienced professional. See listing photos before asking any questions about the installation process.

These spindles have been designed to work with factory hubs, drum brakes and our rear disk conversion kits! They are machined in house and will bolt up to your factory rear axle beams to allow you to use camber shims included in the kit. They will also widen your rear track width approximately 3/8in per side.

Please note that these spindles will not work with other off the shelf camber shim options.

Before ordering it is recommended to have your alignment checked to confirm with shims would be right for you. There are several business's that offer free alignment checks including: Mavis, Pep boys, Firestone, and certain Discount Tire locations.

Using these spindles you are now able to adjust your rear camber on your GE Fit up to 2 degree's and +/- .5 degree of rear toe.

After hearing complaints about the various plastic and aluminum shims on the market feeling flimsy, I decided to machine these from 1018 steel then epoxy powder coated for a long lasting finish.

Spindles start out as a 25lb piece of 4140 steel then get machined down to weighing roughly 3lbs each!

You will receive:

  • 2x custom 4140 steel spindles 
  • 2x camber shims with your choice of either -1 or -2 degree
  • 2x camber shims with +/- .5 toe correction
  • 2x alignment pins for easy installation (see photos)
  • 8x brand new 10.9 grade hardware that are proper length to accommodate for the thickness of the spindles and shims 

Front camber bolts are also available as an optional add on!

If you have any questions feel free to reach out!

 

 

Disclaimer: This product is intended for off-road competition and racing use only. Installation and use on vehicles operated on public roads may violate federal, state, or local laws. The purchaser assumes all responsibility for determining the suitability of this product for its intended application and for complying with all applicable laws and regulations.